Line Dancin

So I removed the old seat and where it used to sit against the fiberglass there are all these little rust stains from where the staples were that held on the vinyl. I have scrubbed these and scrubbed them use a brillo pad and cant get them off. Is there anything I can use to get rid of these rust stains the new seat base is a little smaller and you can see these unsightly stains.

I have the ev 200 sport also on a 22 fter and no issues at all. have it hooed to a hds 5 unit

:thumb:Just ordered a new boat seat from a company called Deckmate boat seats. Had a wise that fell apart and wasn't comfortable from day one. I have to tell ya they had it to me in one day. and the quality is incredible. I will NEVER buy a wise seat again after this one. It was also close to a hundred bucks less than buying a premium wise seat and they shipped it for free. it is made out of a stiffer foam so your butt isn't right on the plastic like the wise because it compress to nothing. They also use better marine grade vinyl than wise does. Needless to say I am very happy with this newer company. If you want to take a look here is their site. http://www.boatseatstore.com/

Of course I found it right after I posted this never mind

OK someone posted that they were going to be doing boat inspections by the fish cleaning station in Holland. For the life of me I cant find that post. Is it this Saturday that they are doing it?

Sounds good. Where did you buy near we are off 12th and Baldwin area

This is what I did. You can call neal at the walker repair facility in Allegan and he has all the parts. I used the old walker motors as they are slower the new motors are to fast. he had used ones at the time for 35 each and I fabbed the rest. I am not sure how much the big jon motors are separately got a couple reverse polarity switches to go into the dash wire it up and I can control my board all from the helm. I had about 150 into the whole project including the mast. http://www.greatlakesfisherman.com/forums/showthread.php?t=32903

Jon I will call you tonight. I will take 2 of them.

We bought a new house in Jenison and are going to be stating to move this weekend. If any of my fishing friends would like to volunteer some help Saturday I would greatly appreciate it afterwards I am getting pizzas and beer for those that help. if you can help send me a pm and I will reply with directions.

LOL frank. I think I am going to pick one up I get a couple gift cards for bass pro to use.

is yours the flex or stiff blade

Ryan was the knife you used the stiff or flex blade?

I really like the handle on them but I saw some of the same type reviews so I figured I would see if any one here had any personal experience with them

Does anyone have the bubba blade filet knife. If so how does it compare to the forschners as far as holding an edge.

I agree with going with the 50/200. Lower freq is better for fresh water opposite for salt. the 50 will penetrate with less distortion then the higher frequencies.

For big weenies I use the entire length tie a loop in the end and good to go

Here is the number for lauvrick 715-394-7671

Rubber bands make a MESS of your boat and they melt and stick to everything. I use 12 lb tst mono for walleye. Just use a good quality release and you wont have to use rubber bands. For eyes I use the yellow offshores and the lauvricks. If you call lauvrick direct they sell a bulk pack of 50 for like 65 bucks. They pull the mini discs and jet 20s fine when I am running jet 40s I use the yellow offshores. To use the offshores for smaller divers only put the line in half way for 40s put in in about 3/4 of the way

Never mind father in law bought one so i am good to go.

Does anyone have a chronograph i could borrow for a day in the greater grand rapids holland area. I am working up loads for evans rifle and need to make sure i am above 1800 fps while reducing recoil as much as possible.

I wouldn't use magdas for wire. I would go to at least convector 30s. The magdas wont hold up to divers especially if you want to run mag divers

We use a lot of dodgers and spin n glos or squids when we target laker. I like my speed about 1.5 mph. and i agree with what rascal said. get your stuff just ticking the bottom.

Nice rig Jon